Top ramps 1.4 tmc2130
If you looking for ramps 1.4 tmc2130 then you are right place. We are searching for the best ramps 1.4 tmc2130 on the market and analyze these products to provide you the best choice.
Best ramps 1.4 tmc2130
1. WitBot MKS Gen L V1.0 Controller Board Integrated mainboard Compatible Ramps1.4/Mega2560 R3 with TMC2130/SPI Motor Driver Kit for 3D Printer
Feature
Aiming at the problems exist on the open sourced controller board such as Ramps 1.4, the developers in Makerbase specially optimize and develop a new product, MKS Gen_L, which provides more flexible choices for users.Use high quality MOSFET tube,better cooling and more stable.Use special power chip,support 12-24V input,to solve the problems of chip heating and power shortage.
Run Marlin firmware, the configuration is completely same as Ramps 1.4, and available to directly replace the Ramps 1.4.
With the TMC2130 V2.0 driver, the driver's chip position is changed inside the driver compared to the TMC2130 V1.1. Support SPI, DIR, DIR mode.
Support a variety of stepper drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change the stepper drivers and motors as users like.Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32.
Description
1.Use CH340 serial port chip, more easily install the drive than 16U2.2. X axis, Y axis and Z axis with different color terminal controls the stepper motors and endstops, which is convenient to wire.
3.Plug the stepper drivers according to the different color terminals which decreases the probability of reverse and prevents the controller board damage.
4.Available to input 24V, the heated bed current can be reduced to 1/4 at the same system power which effectively resolves the problem that the MOSFET of heated bed heats.
5.If you encounter any difficulties when using the TMC2130, please contact us for assistance. We are happy to assist you with this product.
2. GIMAX MKS Gen L V1.0 Integrated Controller PCB Board Reprap Ramps 1.4 Support A4988/DRV8825/TMC2208/TMC2130 Driver for 3D Printer - (Size: with TMC2100)
Feature
Size: With TMC2100Item type: Motherboard
Model number: MKS GEN-L V1.0
Product name: MKS GEN L
Smart controller: Micro switches
Description
IntroductionAiming at the problems exist on the open sourced controller board such as Ramps 1.4, the developers in Makerbase specially optimize and develop a new product, MKS Gen_L, which provides more flexible choices for users.
Features
Support a variety of stepper drivers such as A4988, DRV8825, TMC2130 and LV8729, available to change the stepper drivers and motors as users like.
Reserve external driver signal, available to connect external high-current driver to drive the 57 and 86 stepper motors.
Use high-quality MOSFET, better cooling and more stable.
2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.
Use specific power chip, support 12V-24V power input, and resolve the problems of chip heating and power shortage.
Stable and reliable filter circuit greatly reduces interference and avoids crashes as possible in the process of printing.
Use CH340 serial port chip, more easily install the drive than 16U2.
Run Marlin firmware, the configuration is completely same as Ramps 1.4, and available to directly replace the Ramps 1.4.
Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32.
Available to input 24V, the heated bed current can be reduced to 1/4 at the same system power which effectively resolves the problem that the MOSFET of heated bed heats.
X axis, Y axis and Z axis with different color terminal controls the stepper motors and endstops, which is convenient to wire.
Plug the stepper drivers according to the different color terminals which decreases the probability of reverse and prevents the controller board damage.
Acquire the firmware and drive .Land the website to download:
Type 1 :
Only the board
Type 2 :
Board with 4pcs A4988/DRV8825/TMC2208/TMC2100/TMC2130 DIY Driver(This DIY TMC2130 is not solder resistance and no wire)
Type 3 :
Board with 1 Set TMC2130
3. 3D Printer - Integrated Mainboard MKS Gen-L V1.0 Board MKS Gen L v1.0 Compatible Ramps1.4/Mega2560 R3 +2pcs TMC2130 V1.1 SPI Stepper Drivers
Feature
Package Includes: 1pc MKS Gen L V1.0Control Board | 1pc USB CableItem type: Motherboard
Model number: MKS Gen-L V1.0
Type : MKS GEN-L V1.0 control board
Material: PCB
Description
Integrated Mainboard MKS Gen-L V1.0 Board MKS Gen L v1.0 Compatible Ramps1.4/Mega2560 R3 +2pcs TMC2130 V1.1 SPI Stepper DriversOverview
Aiming at the problems exist on the open sourced controller board such as Ramps 1.4, the developers in Makerbase specially optimize and develop a new product, MKS Gen_L, which provides more flexible choices for users.
Features
1. 2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.
2. Support a variety of stepper drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change the stepper drivers and motors as users like.
3. Reserve external driver signal, available to connect external high-current driver to drive the 57 and 86 stepper motors.
4. Use high-quality MOSFET, better cooling and more stable.
5. Use specific power chip, support 12V-24V power input, and resolve the problems of chip heating and power shortage.
6. Stable and reliable filter circuit greatly reduces interference and avoids crashes as possible in the process of printing.
7. Use CH340 serial port chip, more easily install the drive than 16U2.
8. Run Marlin firmware, the configuration is completely same as Ramps 1.4, and available to directly replace the Ramps 1.4.
9. Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32.
10. Available to input 24V, the heated bed current can be reduced to 1/4 at the same system power which effectively resolves the problem that the MOSFET of heated bed heats.
11. X axis, Y axis and Z axis with different color terminal controls the stepper motors and endstops, which is convenient to wire.
12. Plug the stepper drivers according to the different color terminals which decreases the probability of reverse and prevents the controller board damage.
Package listing:
Package includes:
1pc MKS Gen L V1.0Control Board
1pc USB Cable
4. 3D Printer - 3D printer Board MKS Gen L V1.0 Controller Support A4988/8825/TMC2208/TMC2130 Drivers reprap Ramps1.4/Mega2560 R3 Board - (Size: MKS GEN-L V1.0)
Feature
Size: MKS GEN-L V1.01.Support a variety of stepper drivers such as A4988, DRV8825, TMC2130 and LV8729, available to change the stepper drivers and motors as users like.
2.Reserve external driver signal, available to connect external high-current driver to drive the 57 and 86 stepper motors.
3.Use high-quality MOSFET, better cooling and more stable.
4.2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.
Description
Introduction:Aiming at the problems exist on the open sourced controller board such as Ramps 1.4, the developers in Makerbase specially optimize and develop a new product, MKS Gen_L, which provides more flexible choices for users.
Features:
1.Support a variety of stepper drivers such as A4988, DRV8825, TMC2130 and LV8729, available to change the stepper drivers and motors as users like.
2.Reserve external driver signal, available to connect external high-current driver to drive the 57 and 86 stepper motors.
3.Use high-quality MOSFET, better cooling and more stable.
4.2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.
5.Use specific power chip, support 12V-24V power input, and resolve the problems of chip heating and power shortage.
6.Stable and reliable filter circuit greatly reduces interference and avoids crashes as possible in the process of printing.
7.Use CH340 serial port chip, more easily install the drive than 16U2.
8.Run Marlin firmware, the configuration is completely same as Ramps 1.4, and available to directly replace the Ramps 1.4.
9.Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32.
10.Available to input 24V, the heated bed current can be reduced to 1/4 at the same system power which effectively resolves the problem that the MOSFET of heated bed heats.
11.X axis, Y axis and Z axis with different color terminal controls the stepper motors and endstops, which is convenient to wire.
12.Plug the stepper drivers according to the different color terminals which decreases the probability of reverse and prevents the controller board damag.
Acquire the firmware and drive .Land the website to download:
Item specifics:
Item type: Motherboard
Model number: MKS GEN-L V1.0
Product name: MKS GEN-L
Meterial: PCB
Smart controller: Micro switches
Integrated circuit: Controller panel
Type: MKS GEN-L V1.0
5. KINGPRINT Ramps 1.6 Plus Expansion Control Panel with Heatsink Upgraded Ramps 1.5/1.6 for 3D Printer Board
Feature
The PCB has a built-in selection terminal for driving the SPI working mode, and is compatible with STEP/DIR and SPI modesThe power supply and hot bed use 30A high-current terminal block, to avoid the situation of burning terminals to a greater extent
Added a reset expansion interface, convenient for users to extend the reset button
X, Y, Z, E0, E1 all use parallel dual motor interface, so that the board is suitable for more models
Changed the silk screen, making the wiring clear at a glance. Using a combination of colored pin headers and mothers, effectively distinguishing each functional interface, both beautiful and practical
Description
Highlights:
By using the SPI mode, it is only necessary to perform a simple plug-in operation on the jumper cap, which effectively avoids the problem that the motor does not work due to the wrong line insertion, and also prevents the drive from not working and other issues due to poor contact of the external line during the printing process
Tips:
1. Drive mode selection to determine the firmware to be burned, and pay attention to the consistency of the subdivision
2. When using a hot bed with a power greater than 140w, be sure to install the MOS tube heat sink to prevent the mos tube from overheating. When using a hot bed with a power greater than 180w, be sure to select the hot bed MOS module for transfer. Long-term overheating causes the board to be burned
3. When plugging and unplugging the drive to the Ramps1.6+, pay attention to the direction of the drive, never insert it, prevent the drive from being burned, and the operation of the plug drive must be performed under the premise of power failure. We do not bear the loss and consequences of this type of drive and motherboard being burned due to driver insertion errors.
Package Contents:
1x Ramps 1.6 plus
1x heat sink
NOTE:
If you find any problem, please contact us at first, and our technical staff will help you to solve the problem at once. Thanks!
6. BIQU MKS Gen L V1.0 3D Printer IntegratedMotherboard Controller PCB Board A4988/DRV8825/TMC2208/TMC2130 Like Ramps 1.6 MKS Gen V1.4 Mainboard
Feature
Integrate 2560 and Ramps1.4 one PCB,easier wiring and more stableUse high-quality 4 layer PCB&Use special power chip,support 12V-24V, also Use Marlin firmware,same as configuration way as Ramps1.4, it can replace Ramps1.4 directly
Support a variety of stepper drivers:4988,8825,TMC2208 and TMC2100, and available to work with LCD2004,LCD12864,MKS TFT24/28/32/35 & Available to connect external large stepp drivers
Accept 24V input,reduce the heated bed current to 1/4 that slove the Mosfet heat problem efficiently
Retail Servos,AUX-1 and AUX-2 interface of Ramps1.4 provide three 5V output and three 12V output interfaces
Description
Product Introduction
Aiming at the problems exist on the open sourced controller board such as Ramps 1.4, the developers in Makerbase specially optimize and develop a new product, MKS Gen L, which provides more flexible choices for users.
Attention
1.Make sure positive and negative connection is all right before powering.
2.No plugging and removing the drivers and motors when powering, otherwise it will easily burn the drivers.
3.No adjusting the driver current when the motors are running.
Packing List
MKS GEN L Board1*1
USD Cable*1
7. KINGPRINT 3D Printer MKS Gen V1.4 Controller Board Mega 2560 R3 Motherboard RepRap Ramps1.4 Compatible with USB
Feature
Mega 2560 and ramps1.4 set on a board, to solve complicated Ramps1.4 combination of interfaces, the problem of failure prone.Replace the motor drive, drive and support 4988 8825 drive.
The circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
Using high-quality MOSFET, and better heat dissipation.
Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.
Description
-Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.-Tthe firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.
- Can be connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel.(Can't be sure to match all of stype of 12864LCD and 2004LCD )
- Reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit.
-Reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs.
Specification
Type: MKS Gen V1.4 control board Mega 2560
Name: MKS Gen V1.4 control board
Weight: 118g
Application: 3D Printer Part
Weight: 118g
Package Included:
1* MKS Gen V1.4 Control Board
8. BIQU 3D Printer Part Ultra Silent TMC2208 V1.0 Stepper Motor Driver Module with Heatsink for Control Board MKS GEN V1.4 Ramps 1.4 Ramps 1.6 (Pack of 5pc)
Feature
Flexible microPlyer interpolation unit, the component can provide up to 256 microsteps/step resolution. Even in the limited pulse rate system, it can still be able to achieve sinusoidal control.Because stealthChop fine sound technology is widely used in 3D printing, these components are also designed to be compatible with existing 3D printer electronics, saving the need for costly redesign. Both components have pulse/ direction input, and it can be completely independent operation. The configuration is implemented via digital input.
Based on TRINAMIC TMC 2100 two-phase motor, stepper motor drive board, TRINAMIC TMC 2130 or TRINAMIC TMC 2208, it is compatible with stepstick and pololu a4988 hardware.
SpreadCycle high chopper frequency, dcStep, stallGuard2 stall detection technology.
CoolStep current dynamic adjustment technology, it can save 70% of the energy, StealthChop mute.
Description
Specification :
Interface: Step/Dir
Configuration: CFG Pins or UART
Microplyer/ Microsteps:up to 1/256
Logic Voltage VIO: 3-5V
Motor Voltage VM: 5.5V-36V
Motor Phase Current: 1.2A RMS,2.0A Peak
VM always needed: Yes
Internal V-Regulator: enabled
RDSon: Less than and equal to 0.3 Ohm
StealthChop(quiet):YES
SpreadCycle: YES
CoolStep: no
StallGuard: no
DcStep: no
Instructions:
1. When used on Ramps1.4 or MKS Gen,please remove the 3 jumpers under socket.
2. Pay attention to direction, do not insert wrongly.
3. Heat sink directly attach on the PCB.
4. The motor direction is opposite to that of 4988 and 8825, please adjust the firmware or adjust the motor wiring if you want to replace 4988.
Packing List:
5x TMC2208 Driver
5 x Heat Sink
9. Ramps 1.6 Plus Expansion Control Panel Upgraded Ramps 1.4 3D Motherboard Support A4988 DRV8825 TMC2130 Driver Reprap Mendel for 3D Printer Parts
Description
Packing List
1*Ramps 1.6 Plus control Board
1*Heatsink
Recent Comments