How to find the best brushless whoop dsmx for 2024?
When you want to find brushless whoop dsmx, you may need to consider between many choices. Finding the best brushless whoop dsmx is not an easy task. In this post, we create a very short list about top 10 the best brushless whoop dsmx for you. You can check detail product features, product specifications and also our voting for each product. Let’s start with following top 10 brushless whoop dsmx:
Best brushless whoop dsmx
1. BETAFPV Beta75X 2S Brushless Whoop Drone with 2S F4 FC Frsky Z02 Camera OSD Smart Audio 11000KV 1103 Motor XT30 Cable for Tiny Whoop FPV Racing
Feature
In the Beta75X BNF setup, when you connect the receiver to 2S FC, don't forget to plug the battery, otherwise the receiver will have no power to work at all.Durable and light frame is customed for the Beta75X. Only 41g give pilots a good weight balance and nice punch on 2S battery, 300mAh 2S HV battery is recommended in default. But pilot could also use their whoop batteries with a replaced power cable. Optional and affordable.
Whole drone no soldering or tinkering necessary. Customed lightest 1103 11000KV motors with cable connectors. Just plug and play. And the camera is the Z02 AIO VTX, spilt and 35 camera mount for more fast flying, smartaudio and output power switchable is also available for VTX remote control.
The Beta75X drone comes with "props out" in default. With reversed props or "props out", so no more dipping even in hardest cornering. More details please check https://betafpv.freshdesk.com/support/solutions/articles/27000050781-know-more-about-props-out-
With the high performance STM32F405 processor FC boards and tuned Betaflight Ominibus 3.5.0 firmware, everyone could fly the Beta75X drone like a racing professor.
Description
BETAFPV Beta75X 2S Brushless Whoop Quadcopter Frsky OSD Smartaudio with 1103 11000KV Motor XT30 Cable for FPV Racing Whoop
Here is a introducing video shared by Nate Payne:
https://www.youtube.com/watch?v=JHH17wrMbg0&feature=youtu.be
SPECIFICATION
Weight: 41g (without battery)
Motors: 1103 11000KV with connector
Props: 40mm 4-blades props, 1.5mm shaft hole
Recommend battery: 350mAh 2S battery
Receiver Option: Frsky
FC
CPU: STM32F405
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD) 3.5.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Smart Audio port is available for radio control VTX
ESC
Support BLheli/BLHELI_S suite Pass-through ready
Dshot600 in default
Input voltage: 2S lipo
Cotinue current: 6A
Peak current: 10A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
Z02 AIO Camera VTX -- On the Beta75X, it is the customed version with VTX board and camera board split.
Smart Audio function is included for radio control
Output power: 0mW, 25mW and 200mW (Adjustable)
Antenna: Dipole ANT
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
TV System: NTSC
Field of view: 100-120 degrees with 1/4 lens
Recommend Part:
2S Brushless FC:www.amazon.com/dp/B07H8XQ7R6
300mAh 2S Battery:www.amazon.com/dp/B07H8G5ZPW
1103 Motor:www.amazon.com/dp/B07FN64599
Z02 Cam:www.amazon.com/dp/B07FNRLFGZ
Beta75X Frame Kit: www.amazon.com/dp/B07GYJP8HF
40mm Prop: www.amazon.com/dp/B07H9B2GJH
Package:
1 * Beta75X BNF 2S Whoop Quadcopter
1 * 300mAh 2S 35C-75C battery
1 * Spare 40mm 4-blades props (2CW+2CCW)
1 * Spare Canopy
2. BETAFPV Beta75X 2S Whoop Frame Kit with 2 Sets 40mm 4-Blade Props 1.5mm Shaft Blue for 75mm 2S Brushless Whoop Drone Like Beta75X BNF
Feature
Betafpv Beta75X 2S Whoop Frame is designed for 75mm 2S whoop drone, with a customed battery slot to support 2S battery or 2pcs 1S battery series connection, can fit with 110x motors.The light and durable frame is clear plastic material only 7.1g/pcs, with a 26mm x 26mm FC mounting columns can match whoop style flight controller.
There are 2 sets 40mm 4-blade props 1.5mm shaft hole in this kit, can fit the 110x motors perfectly, only weighs 2.4g/set.
If order this kit, highly recommend our Betafpv 300mAh battery and 1103 brushelss motors for DIY your Beta75X 2S Brushless BNF.
Any technical support needed please contact: [email protected]
Description
BETAFPV Beta75X 2S Whoop Frame Kit with 2 Sets 40mm 4-Blade Props 1.5mm Shaft Blue for 75mm 2S Brushless Whoop Drone like Beta75X BNF
Specifications:
Frame
Material: Clear plastic
Diagonal motor to motor distance: 75mm
Motor mounting hole: for 110x series motors
FC mounting hole: 26mm x 26mm, fully compatible with whoop style FC board mounting pattern
Battery slot size: 11.5x16mm, for BETAFPV 300mAh battery
Weight: 7.1g/pcs
Propellers
Prop: 40mm 4-blade props
Material: Clear plastic
Inner diameter: 1.5mm Shaft
Product material: Clear Plastic
Color: Blue
Weight (2CW+2CCW): 2.40(g) = 0.08(oz)
Recommend Parts:
Batteries: 300mAh 2S Lipo HV batteries
Motors: 110x brushless motors, like 1103 11000KV motors
FC: Betafpv 2S Brushless FC
Package:
1 * Beta75X frame for 75mm 2S whoop drone
8 * 40mm 4-blade 2S Whoop Propellers (4CW + 4 CCW)
3. BETAFPVBeta65X2SBrushlessWhoopDronewith2SF4FCDSMX Z02CameraOSDSmartAudio17500KV0802MotorPH2.0CableforTinyWhoopFPVRacing
Feature
In the Beta65X BNF setup, when you connect the receiver to 2S FC, don't forget to plug the battery, otherwise the receiver will have no power to work at all.The DSMX receiver used on the 65X is different from the one we used before. The binding procedure is also different. Check out the details on the support link below. http://support.betafpv.com/support/solutions/articles/27000051188-cli-dump-of-beta65x-and-beta75x-dsmx-version.
The Beta65X drone comes with "props out" in default. With reversed props or "props out", so no more dipping even in hardest cornering. More details please check https://betafpv.freshdesk.com/support/solutions/articles/27000050781-know-more-about-props-out-
Durable and light enough frame is customed for the Beta65X. A total weight of 26g give pilots a good balance of weight and nice punch on HV battery. 2pcs 1S 300mAh Lipo HV batteries are recommended in default. So pilot could also use their whoop batteries.
Whole drone no soldering or tinkering necessary. Customed lightest 0802 17500KV motors with cable connectors. Just plug and play. And the camera is the Z02 AIO VTX, spilt and 35 camera mount for more fast flying, smart audio and output power switchable is also available for VTX remote control.
Description
BETAFPV Beta65X 2S Brushless Whoop Quadcopter Frsky OSD Smartaudio with 0802 17500KV Motors for FPV Racing Whoop
Here is a introducing video shared by Daniel Sugano:
https://www.youtube.com/watch?v=faen8NN5GcI&feature=youtu.be
SPECIFICATION
Weight: 26g (without battery)
Motors: 0802 17500KV with connector
Props: 31mm 4-blades props, 1.0mm shaft hole
Camera tilt angle: 35 degree
Receiver Option: Frsky XM / FullSpeed DSMX
Batteries: 300mAh 1S Lipo HV batteries
FC
CPU: STM32F405
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD) 3.5.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Smart Audio port is available for radio control VTX
ESC
Support BLheli/BLHELI_S suite Pass-through ready
Dshot600 in default
Input voltage: 2S lipo
Cotinue current: 6A
Peak current: 10A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
Z02 AIO Camera VTX -- On the Beta65X, it is the customed version with VTX board and camera board split.
Smart Audio function is included for radio control.
Output power: 0mW, 25mW and 200mW (Adjustable)
Antenna: Dipole ANT
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
TV System: NTSC
Field of view: 100-120 degrees with 1/4 lens
Recommend Part:
2S Brushless FC: www.amazon.com/dp/B07H8XQ7R6
260mAh Battery: www.amazon.com/dp/B07121V7MB
0802 Motor: www.amazon.com/dp/B07GYR31T8
Z02 Cam: www.amazon.com/dp/B07FNRLFGZ
31mm Prop: www.amazon.com/dp/B07D7WSL3L
Package:
1 * Beta65X BNF 2S Whoop Quadcopter
2 * 300mAh 1S Lipo HV batteries
1 * Spare 31mm 4-blades props (2CW+2CCW)
1 * Spare Canopy
4. BETAFPV FPV FC F3 Brushless 1S Flight Controller Integrated with ESC and OSD No Receiver Version
Feature
The world's first compatible BetaFlight OSD, BLHeli_S ESC, BetaFlight firmware, acro F3 flight controller for the Micro brushless Whoop quadcopter.Fully programmable through Betaflight firmware, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings.
Built in ESC support 5A continuous current and peak 6A (3 seconds), Support BLHeliSuite programmable.
Compatible Receivers signal include PPM, SBUS, IBUS, Spektrum DSM2 / DSMX, 1024/2048 etc.
The flight controller board comes pre-flashed with Betaflight firmware. Some basic guidance and typical FAQ, please check it here : https://betafpv.freshdesk.com/support/solutions
Description
SPECIFICATIONS FC
CPU: STM32F303CCT6 (72MHZ, 256K FLASH)
Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
Size: 26mm x 26mm, fully compatible with the Inductrix quad frame, Beta65 Pro frame, Beta75 Pro frame, BWhoop B06 frame and mounting pattern
Firmware version: betaflight_3.2.0_BETAFLIGHTF3 / betaflight_3.2.0_OMNIBUS (old version)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 3.2g
BETAFPV Support Freshdeskhttps://betafpv.freshdesk.com/support/solutions/articles/27000038661-betaflight-osd-setup
ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
The upgraded FC board is for betaflight_3.2.0_BETAFLIGHTF3 firmware.
Note: The issue of motor not spin up properly :https://betafpv.freshdesk.com/support/solutions/articles/27000045214-troubleshooting-motor-doesn-t-spin
BetaFlight OSD
Betaflight OSD (on screen display) is integrated in BETAFPV F3 brushed flight controllers that shows important flight data on your FPV feed, such as battery voltage, current draw and much more. You can even use it as a menu to change your quad's PID, rates, filters and other settings.
Package
1 * F3 1S brushless flight controller
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers
5. BETAFPV F4 FC 1S Brushless Flight Controller ESC OSD Smart Audio (No RX) FPV Tiny Whoop Micro Racing Drone Beta75pro Beta65pro
Feature
This is upgraded F4 Brushless FC No RX based on F3 version, MCU has upgraded to STM32F411 100MHz with faster processing rate(from 72MHz to 100MHz). Build-in Betaflight OSD and polar reversed protection. Suitable for 1S brushless whoop drone Beta65 Pro, Beta75 Pro, BWhoop B06 etc.High-performance ST Microelectronics ARM Cortex-M4 core F411 100MHz CPU (safely overclocked to 120MHz).30A continuous drain current MOSFET. Lower to 8.5m inner resistance value (4.5V). It has a noticeable power improvement in low battery voltage status or with 8x20/8.5x20 motors.
The F4 1S brushless FC comes with no receiver, compatible receivers signal include PPM, SBUS, IBUS, Spektrum DSM2 / DSMX, 1024/2048 etc. The flight controller board comes pre-flashed with Betaflight firmware.
Fully programmable through Betaflight firmware, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings.
The output voltage for receiver is switchable between 3.3V and 5V. So pilots could use Spektrum receiver that need 3.3V power. 3.3V in default. Built in ESC support 5A continuous current and peak 6A (3 seconds), support BLHeliSuite programmable.Some basic guidance and typical FAQ, please check it here : https://betafpv.freshdesk.com/support/solutions
Description
BETAFPV F4 1S Brushless Flight Controller FPV FC Integrated with ESC OSD Support SmartAudio (No RX) for 1S FPV Micro Brushless Racing Drone like Beta75 pro Beta65 pro
Specifiction
FC
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
Size: 26mm x 26mm, fully compatible with the Inductrix quad frame, BWhoop B06 frame and mounting pattern
Firmware version: betaflight_3.5.0_MATEKF411.hex
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 4g
ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Recommend Parts List
Frame:
Beta65 Pro frame-www.amazon.com/dp/B078GLW4HK
Beta75 Pro frame-www.amazon.com/dp/B078H7R3PV
Props:
31mm 4-Blades props (for Beta65 Pro)-www.amazon.com/dp/B07D7WSL3L
40mm 4-blades props (for Beta75 Pro)-www.amazon.com/dp/B07B2P7TF4
Receiver: XM Receiver / XM+Receiver / Fullspeed DSMX Receiver / Futaba RX800-PRO Receiver / Flysky RX2A Pro Receiver
Motors:
0703 motors-www.amazon.com/dp/B078N93QVP
0603 motors-www.amazon.com/dp/B079HXLJJ5
Package List:
1 * F4 1S brushless flight controller
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers
6. BETAFPV DSMX Receiver Compatiable with DSM2 DSMX Series Transmitter for Micro FPV Tiny Whoop Drone
Feature
It's the newest BETAFPV DSMX Receiver designed for Micro FPV tiny whoop drone. Compatible with DSM2 or DSMX protocol series of remote transmitter.The detailed bind procedure please check here: https://betafpv.freshdesk.com/support/solutions/articles/27000051474-how-to-bind-the-spekturm-radio-transmitter-to-fullspeed-receiver
The DSMX Receiver can work with all of our FCs without Rx, like F4 1S brushed, F4 1S brushless and F4 2S brushless FC No Rx.
Only weighs 0.6g/pcs and long range distance of 300m.
BETAFPV Micro DSMX Receiver include antenna comes with a clear heatshrink tubing and 3 silicone wires.
Description
BETAFPV DSMX Receiver Compatiable with DSM2 DSMX Series Transmitter for Micro FPV Tiny Whoop Drone
The detailed binding procedure please check here:
https://betafpv.freshdesk.com/support/solutions/articles/27000051474-how-to-bind-the-spekturm-radio-transmitter-to-fullspeed-receiver
SPECIFICATION
Input power: 5V
Frame rate: 22ms/11ms
Resolution: 2048
Working current: 60MA
Weight: 0.6g
Receive sensitivity: -108DBM
Delay: <15ms
Antenna length: 80MM Antenna
Data format: DSMX
Distance: 300m
Channels: support 6-8 channels
Compatible Transmitters: DSM2 / DSMX series of remote transmitter
RECOMMEND PART
F4 1S Brushed FC(No RX)-www.amazon.com/dp/B07HCBKQM4
F4 1S Brushless FC(No RX)-www.amazon.com/dp/B07JG2DH3C
F4 2S Brushless FC(No RX)-www.amazon.com/dp/B07H8XQ7R6
PACKAGE
1 * BETAFPV Micro DSMX Receiver (Include antenna)
1 * Clear heatshrink tubing
1 * Silicone Wire (Black)
1 * Silicone Wire (Red)
1 * Silicone Wire (Yellow)
7. BETAFPV 2S F4 FC Brushless Flight Controller ESC OSD Smart Audio (No RX) with XT30 Cable for 2S Brushless FPV Whoop Drone Beta75X Beta65X
Feature
The F4 2S brushless flight controller and ESC built-in BetaFlight OSD is customized for 2S whoop drone like Beta75X and Beta65X. Please note: When you connect the receiver to this 2S FC, don't forget to plug the battery, otherwise the receiver will have no power to work at all.This combo F4 2S FC with ESC is customized to work with 2S 350mAh battery for Beta75X, which will bring your drone a nice punch. If you want to use it with your own 1S whoop battery, please change the cable to JST-PH2.0 -- https://www.amazon.com/dp/B07GXBF8VN.
Please note this F4 2S FC is built without receiver, but all the ports are available on this board, you could connect any receiver you want, like Frsky, TBS or DSMX Receiver, and Buzzer solder pads is also available. Receiver Connection: https://betafpv.freshdesk.com/support/solutions/articles/27000049913-f4-2s-brushless-fc-esc
Firmware version of F4 FC is Betaflight OMNIBUSF4SD (OBSD), Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode). Support TBS micro receiver with TX02, RX02 ports. RSSI ports is available. Any technical support needed please contact: [email protected].
This ESC support BLheli/BLHELI_S suite Pass-through ready, support PPM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600.It can fit motors with 1.5mm header pins connector like 0703, 0603,1103 motors etc, and you can use it work with the 1pcs 2S 300mAh battery or 2pcs 1S 260mAh battery.
Description
BETAFPV F4 2S FC Brushless Flight Controller and ESC Support SmartAudio OSD with XT30 Cable for Beta65X Beta75X 2S Brushless Whoop Drones
How to connect the receiver and configure in Betaflight, please check the details here:
https://betafpv.freshdesk.com/support/solutions/articles/27000049913-f4-2s-brushless-fc-esc
SPECIFICATIONS:
Item: F4 2S Brushless Flight Controller
CPU: STM32F405 (Overclock to 240MHz)
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
TX02RX02 ports is available, so that it could support TBS micro receiver
RSSI ports is available
Buzzer and LED strip solder pads
Weight: 2.7g
ABOUT ESC:
Support BLheli/BLHELI_S suite Pass-through ready
Support PPM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S lipo
Cotinue current: 10A
Peak current: 15A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
Motor Connectors: 1.25mm header pins connector
RECOMMENDED PARTS LIST
Cam: Z02 Cam- www.amazon.com/dp/B07FNRLFGZ
Frame:
Beta65X frame kit- www.amazon.com/dp/B07GYL2JT6
Beta75X frame kit- www.amazon.com/dp/B07GYJP8HF
Motors:
0802 motors-www.amazon.com/dp/B07GYR31T8
1103 motors-www.amazon.com/dp/B07FN64599
Battery: 350mAh 2S Battery-www.amazon.com/dp/B07JG3ZFC5
Cable:
XT30 cable-www.amazon.com/dp/B07FFQ2TXQ
JST2.0 cable-www.amazon.com/dp/B07GXBF8VN
Package:
1 * F4 2S brushless flight controller with XT30 cable
1 * 4in1 10A ESC board
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers
8. Happymodel Mobula7 Quadcopter Indoor Four-axis 2S 75mm Brushless Whoop Racer Drone BNF Without Remote Controller (Receiver for DSM2/DSMX Version)
Feature
Without Remote ControllerReceiver:DSM2/DSMX Receiver,support DSM2 and DSMX compatible Spektrum transmitter
Full telemetry function ready
Head lights ready
Camera angle adjustable
Description
Specifications:Brand Name: Happymodel
Mode Name: Mobula7
Item Name: 2S 75mm Brushless Whoop racer drone BNF
Version: DSM2/DSMX version
Receiver:DSM2/DSMX Receiver
DSM2/DSMX version support DSM2 and DSMX compatible Spektrum transmitter
Wheelbase: 75mm
Size: 98mm*98mm*36mm
Weight: 25.9g(without battery)
Weight:40g(with Original 250mah lipo battery x2 )
Features:
- New Crazybee F3 PRO Flight controller 1-2s Lipo compatible
- 2S whoop more powerful and more flight time
- Betaflight support , multi flight mode: ACRO/AIR/ANGLE
- New 0802 Powerful and High efficiency Brushless motor and Smooth ESC
- Adjust the settings and the PID of the flight controller via OSD
- Full telemetry function ready
- Head lights ready
- Camera angle adjustable
- Real Bind and Fly version
- Buzzer Ready
Package Included:
1x Mobula7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
4x 3.8v 250mah 30C/60C Lipo battery
1x 1S06 6 Way Lipo/LIHV charger
1x Propeller Disassemble Tool
1x Fixing Mount for Lipo Battery
1x Screwdriver
9. HAPPYMODEL Crazybee F4 Pro 1-2S Compatible Flight Controller for Brushless Whoop Internal DSMX Protocol RX
Feature
HappymodelCrazybee-F4-PRO-V1.0-DSMX-version
Description
Happymodel Crazybee F4 Pro 1-2S compatible flight controller for Brushless whoop Internal DSMX protocol RX10. QWinOut Happymodel Mobula7 Quadcopter Indoor Four-axis 2S 75mm Brushless Whoop Racer Drone BNF (DSM/2 DSM/X Receiver Standard Version)
Feature
Option: Basic Version (comes with USB Lipo/LIHV Charger)//Standard Version(comes with 1S06 6 way Lipo/LIHV charger). Receiver option: Frsky Non-EU version support NON-EU Frsky transmitter D8/D16 compatible; Flysky version support both AFHDS and AFHDS-2A protocol transmitter; DSM2/DSMX version support DSM2 and DSMX compatible Spektrum transmitter; Frsky EU-LBT version support Frsky EU-LBT firmware transmitterMode Name: Mobula7; Item Name: Happymodel 2S 75mm Brushless Whoop racer drone BNF; Wheelbase: 75mm
New Crazybee F3 PRO Flight controller 1-2s Lipo compatible; 2S whoop more powerful and more flight time; New 0802 Powerful and High efficiency Brushless motor and Smooth ESC
Betaflight support , multi flight mode: ACRO/AIR/ANGLE; Betaflight OSD support ,easy to get RSSI, Voltage ,current from your goggles(DSMX version no RSSI output)
Smartaudio ready , change VTX bands, channels via OSD (Adjust the settings and the PID of the flight controller via OSD); Full telemetry function ready; Head lights ready; Camera angle adjustable; Real Bind and Fly version; Buzzer Ready
Recent Comments