Expert choice for arduino touch sensor
When you want to find arduino touch sensor, you may need to consider between many choices. Finding the best arduino touch sensor is not an easy task. In this post, we create a very short list about top 10 the best arduino touch sensor for you. You can check detail product features, product specifications and also our voting for each product. Let’s start with following top 10 arduino touch sensor:
Best arduino touch sensor
1. WMYCONGCONG 20 PCS TTP223B Digital Touch Capacitive Sensor Switch Module DIY for Arduino (20PCS)
Feature
Low power consumption.Power supply: 2 - 5.5V DC.
Great replacement for the traditional touch of a button.
4 M2 screws positioning holes for easy installation.
Size: 24 x 24 x 7mm/9.45 x 9.45 x 2.76inch (L x W x H).
Description
Specification:Low power consumption
Power supply for 2 - 5.5V DC
Can replace the traditional touch of a button.
Four M2 screws positioning holes for easy installation.
The module is a capacitive touch-type touch switch module based on a touch detection IC (TTP223B). Normally, the module outputs a low level, and the mode is a low power mode; when the corresponding position is touched with a finger, the module outputs a high level, and the mode switches to a fast mode; when there is no touch for 12 seconds, the mode is switched to a low mode. Power mode. The module can be mounted on the surface of non-metallic materials such as plastic and glass, and a thin piece of paper (non-metal) can be placed on the surface of the module. As long as the touch is correct, it can be hidden in the wall, desktop, etc. button. This module allows you to eliminate the hassle of conventional push buttons.
Package Content:
20 * TTP223B Digital Touch Sensor Module
2. HiLetgo 10pcs TTP223B Switch Module Digital Touch Sensor Capacitive Touch for Arduino
Feature
This is the "momentary" variety of the touch sensor - touch and it turns on, release and it turns off.Positive and negative can be used as a touch surface,can replace the traditional touch button.
Four M2 screws positioning holes for easy installation.Module can be installed in such as surface plastic, glass of non-metallic materials.
In addition to the thin paper ( non-metallic ) covering the surface of the module , as long as the correct location of the touch , you can make hidden in the walls, desktops and other parts of buttons.
The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption; When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode.
Description
Project Scope(for reference):1.With the optocoupler + bi-directional thyristor can be completed touch fluorescent lamps and other smart home projects
2.With the optocoupler + delay + bidirectional thyristor stairs to complete the touch lamp
Features:
Low power consumption
Power supply: 2 ~ 5.5VDC
This module can replace the traditional touch button
Four M2 screws positioning holes for easy installation
Specification:
Power supply voltage VCC: 2.0--5.5 V(Typical 3V)
Output high VOH: 0.8VCC
Output low VOL: 0.3VCC
Output Pin Sink Current (@ VCC = 3V, VOL = 0.6V): 8mA
Output pin pull-up current (@ VCC = 3V, VOH = 2.4V): 4 mA
Response time (low power mode): 220 mS
Response time (touch mode): 60 mS
Size: 24x24x7.2 mm
Weight: 2g
Package Include:
10* TTP223B Switch Module Digital Touch Sensor
3. Anmbest 20PCS 2.5-5.5V TTP223 Capacitive Touch Switch Button Self-Lock/No-Lock Module for Arduino
Feature
MAIN SPECIFICATIONS: Power:2.5-5.5V; Multiple trigger mode; Size: 15mm x 11mm 0.59"x 0.43".HIGH RELIABILITY: This module is based on a touch detection IC ( TTP223 ) of capacitive type touch jog switch module. Stable touching detection of human body for replacing traditional direct switch key.
HIGH AVAILABILITY: A very useful addition for projects or applications where a conventional mechanical button or switch is not an ideal choice.
EASY TO INSTALL: The module can be installed in plastic, glass surface non-metallic materials. As long as the touch of the correct position, you can make hidden in the wall, desk and other places.
SMALL SIZE&LIGHT WEIGHT: Size: 15mm x 11mm 0.59"x 0.43" (LxW); Net weight: approx. 8g; Package Included: 20x Capacitive Touch Switch Button Self-Lock Module.
Description
This module is based on a touch detection IC ( TTP223 ) of capacitive type touch jog switch module. This touch detection IC is designed for replacing traditional direct button key with diverse pad size.Specifications:
Power:2.5-5.5V
Trigger setting mode:(1->Short;0->No Short)
AB=00:No-lock High TTL level ouput;
AB=01:Self-lock High TTL level ouput;
AB=10:No-lock Low TTL level ouput;
AB=11:Self-lock Low TTL level ouput
Size: 15mm x 11mm 0.59"x 0.43" (LxW)
Net weight: approx. 8g
Package Included:
20x Capacitive Touch Switch Button Self-Lock Module
4. 10PCS TTP223 Capacitive Touch Switch Button Self-Lock Module for Arduino
Feature
Modes: jog, self-lockingVoltage: 2.5-5.5V
Module size:15*11mm
10pcs in one package
Funny DIY Expert, the best chioce for DIY
Description
Modes: jog, self-lockingVoltage: 2.5-5.5V
Module size:15*11mm
Package Include:
10Pcs TTP223 Capacitive Touch Switch Button Self-Lock Module for Arduino
5. WINGONEER DIY 5PCS TTP223B Digital Touch Capacitive Sensor Switch Module for Arduino
Feature
Low power consumptionPower supply for 2 ~ 5.5V DC
Can replace the traditional touch of a button
Four M2 screws positioning holes for easy installation
Size:2.4 x 2.4 x 0.7cm(LxWxH)
Description
WINGONEER trademark Reg.NO:4747611Features:
The module is based on a touch-sensing IC TTP223B capacitive touch switch module. In the normal state, the module output low, low power consumption, but when a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode.Module can be installed in such as surface plastic, glass of non-metallic materials.You can put to a thin non-metallic paper cover the surface of the module , when touch the correct location of the module , that you can put it hidden in the walls, desktops and other buttons.Low power consumption.Green LED Indicator, and it is bright when power on right.Both positive and negative can be used as a touch surface, and replace the traditional touch of a button.
include
5x WINGONEER TTP223B Digital Touch Capacitive Sensor Switch Module for Arduino
6. Adafruit 12-Key Capacitive Touch Sensor Breakout - MPR121
Feature
Adafruit Part Number: 1982Stock Type: Sensors >> Touch
In Stock & Ready to Ship
Description
Add lots of touch sensors to your next microcontroller project with this easy-to-use 12-channel capacitive touch sensor breakout board, starring the MPR121. This chip can handle up to 12 individual touch pads.
The MPR121 has support for only I2C, which can be implemented with nearly any microcontroller. You can select one of 4 addresses with the ADDR pin, for a total of 48 capacitive touch pads on one I2C 2-wire bus. Using this chip is a lot easier than doing the capacitive sensing with analog inputs: it handles all the filtering for you and can be configured for more/less sensitivity.
This sensor comes as a tiny hard-to-solder chip so we put it onto a breakout board for you. Since it's a 3V-only chip, we added a 3V regulator and I2C level shifting so its safe to use with any 3V or 5V microcontroller/processor like Arduino. We even added an LED onto the IRQ line so it will blink when touches are detected, making debugging by sight a bit easier on you. Comes with a fully assembled board, and a stick of 0.1" header so you can plug it into a breadboard. For contacts, we suggest using copper foil or pyralux, then solder a wire that connects from the foil pad to the breakout.
Getting started is a breeze with our Arduino library and tutorial. You'll be up and running in a few minutes, and if you are using another microcontroller, its easy to port our code.
Of course, we wouldn't leave you with a datasheet and a "good luck!" - we wrote a detailed tutorial showing how to wire up the sensor, use it with an Arduino and example code that g ets the sensor logging data anddetecting yourtouch!
7. SMAKN TTP223B Digital Touch Sensor Capacitive Touch Switch Module for Arduino Raspberr
Feature
TTP223 Capacitive Touch Switch Digital Touch Sensor Module for Arduino UNO DUE MEGATTP223 capacitive touch single IC.
On board level indicator.
Working voltage: 2.0V to 5.5V.
Size: 29(mm) x16(mm).
Description
Description:1TTP223 capacitive touch single IC.
2On board level indicator.
3Working voltage: 2.0V to 5.5V.
4Size: 29(mm) x16(mm).
Package Included: TTP223 Capacitive Touch Switch Module
8. DFRobot Gravity: Digital Capacitive Touch Sensor for Arduino
Feature
This arduino digital capacitive touch sensor provides a one-touch style switch on your Arduino projectIt uses the most popular capactiive sensing technology which is the same as your mobile phone
This little sensor can "feel" people and metal touch and feedback a high/low voltage level
Even isolated by cloth or paper, it still can feel the touch
This sensor can work at 3.3V which make it compatible with Raspberry Pi, intel edison, joule and curie
Description
INTRODUCTIONThis Arduino digital capacitive touch sensor provides a one-touch style switch on your Arduino project. It uses the most popular capacitive sensing technology which is the same as your mobile phone.
Getting tired with clicking mechanic button? Try this capacitive touch sensor. Right now we can find touch sensor on most electronic device. So upgrade your Arduino project with our new version touch sensor and make it cool!!
This little sensor can "feel" people and metal touch and feedback a high/low voltage level. Even isolated by cloth or paper, it still can feel the touch. The sensitivity will decrease as the isolation getting thick. For detail of usage, please check its wiki.
To ease the difficult of using this sensor, a Gravity Interface is adapted to allow plug&play. The IO expansion shield is the best match for this sound senor connecting to your Arduino. As this sensor can work at 3.3V which make it compatible with Raspberry Pi, Intel Edison, joule and curie.
If you want to start playing with sensors, Gravity: 27 Pcs Sensor Kit for Arduino is a great choice for you to learn varieties of sensors.
FEATURES
Wide voltage range from 3.3V to 5V
Standard assembling structure (two 3mm holes with multiple of 5cm as interval)
Easily recognitive interfaces of sensors ("A" for analog and "D" for digital)
Icons to simplify illustrate sensor function
High quality connector
Immersion gold surface
SPECIFICATION
Supply Voltage: 3.3V to 5V
Interface: Digital
Size: 22x30mm (0.87 x 1.18 in)
SHIPPING LIST
Capacitive Touch Sensor x1
Digital cable x1
9. SMAKN TTP224 4-way Capacitive Touch switch Digital Touch Sensor Module for Arduino
Feature
Onboard TTP224 capacitive touch sensor IC 4 keys4 board-level status indicator
Working voltage: 2.4V-5.5V
PCB board size: 35 (mm) x29 (mm)
Description
the module can set the output mode, the key output mode, the maximum output time and fast / low power selection10. Adafruit Standalone Momentary Capacitive Touch Sensor Breakout
Feature
Adafruit Part Number: 1374Stock Type: Sensors >> Touch
In Stock & Ready to Ship
Description
This breakout board is the simplest way to create a project with a single "momentary" capacitive touch sensor. No microcontroller is required here - just power with 1.8 to 5.5VDC and touch the pad to activate the sensor.
When a capacitive load is detected (e.g. a person touches the sensor-pad area) the red LED lights up and the output pin goes high. You can also solder a wire to the middle pad and create your own capacitive pad if the built-in one isn't suited to your project.
If you want to save power, the LED can be disconnected from the output pin (cut the trace between the jumper marked as such). We designed this breakout to have the more-responsive "fast mode" which draws about 0.5mA. If you need ultra-low (~50uA) power usage, the mode jumper can be cut on one side & soldered closed on the other to fix it into that mode. Check the datasheet for specific power usage measurements.
Comes with a fully assembled board, and a small stick of 0.1" header so you can solder and plug it into a breadboard. For additional contacts, we suggest using copper foil, then solder a wire that connects from the foil pad to the breakout.
The datasheet has many details on sensitivity, power usage, etc.
Standalone Momentary Capacitive Touch Sensor Breakout ( 11:10 )
Recent Comments