10 best malco shears drill attachment for 2024
It took days of going through more than a thousand customer reviews and conducting expert researches to narrow down the list. Weve included a comparison table below to give you a quick summary of our top 10 malco shears drill attachment. Its followed by an in-depth review of each malco shears drill attachment. Hopefully, once you are done reading this article, you will be well informed about malco shears drill attachment and be able to select the right malco shears drill attachment for you without any hesitations.
Best malco shears drill attachment
1. Malco TSCM Corrugated Metal Turbo Shear
Feature
Attaches to a drill or impact driver you already ownMake fast cross-cuts, lengthwise trim cuts in large or small metal corrugated patterns
360 degree rotating head for optimum tool clearance and material flow
Able to cut curves and straight lines
Made in the USA
2. Malco TSHD1 Automotive Heavy Duty 18 Gauge Turbo Shear Drill Attachment
Feature
Fits cordless drillsCuts straight and left
Lightweight
Telescoping drill clamp
Wide jaw opening
3. Malco TS1 Turbo Shear 20 Gauge Capacity Sheet Metal Cutting Attachment
Feature
Turns your power drill into a power shearInserts into chuck of an A/C or cordless drill
20 gauge capacity in galvanized steel
Navigates tight patterns and square cuts
TSDC Drill Clamp can be purchased separately
Made in the USA
4. Malco TSHD Turboshear Heavy Duty Metal Cutting Attachment Shear , Black
Feature
Made in the USAReplaceable blades
Turns your power drill into a heavy duty power shear
Inserts into the chuck of a 14.4 volt or larger A/C or cordless drill
Capacity to cut 18 gauge galvanized steel and 20-gauge spiral duct
Navigates tight patterns and square cuts
Clamping devise is included
5. Malco TSDC Drill Clamp for 1ELH1 Shear
Feature
Makes cutting with the TurboShear model TS1 a one-handed operationRails of the drill clamp are easily attached to the TS1 TurboShear, and positioned over the body of the drill
Compatible with all current and pre-existing Malco TurboShear drill attachments
Made of strong but lightweight aluminum
Fits most 1200 RPM or larger cordless or A/C drills
Made in the USA
6. Malco TSF1 Turboshear Fiber Cement Siding Shear
Feature
Attaches to a drill or impact driver you already ownEasily cuts 5/16-inch Fiber Cement Siding Plank with minimal dust
360 degree rotating head for optimum tool clearance and material flow
Able to cut precise arcs, straight lines and fine trimming
Made in the USA
7. Double Headed Sheet Metal Nibbler, REXBETI Drill Attachment Metal Cutter with Extra Punch and Die, 1 Cutting Hole Accessory and 1 Step Drill Bit, Perfect for Straight Curve and Circle Cutting (gold)
Feature
Easy and fast to cut 14 gauge material and creates a precision, burr free edge360 degree double cutting head to cut straight line, curve line and circles
HSS cutting blades to cut including but not limited to: Sheet metal, corrugated material, pipes, complex profiles, powder coated material, stainless steel, copper, aluminium, formica, plastic, fibreglass
Fits any drill that works between 1500-3000 RPM, More easy and powerful than normal shears and snips
REXBETI versatile sheet metal nibbler, perfect for car repair and house maintenance like metal roof cutting, HVAC vent pipe and other metal sheets
8. Malco TSF2 TurboShear Fiber Cement Backer Board Shear
Feature
Attaches to a drill or impact driver you already ownEasily cuts 1/2-inch backer board and 5/16-inch Fiber Cement Siding Plank with minimal dust
360 degree rotating head for optimum tool clearance and material flow
Able to cut precise arcs, straight lines and fine trimming
Made in the USA
9. Malco TSMD Corrugated Metal Turbo Shear Attachment
Feature
Fits a drill you already ownProduces clean edge on both sides of cut
Approaches cut from either end
Navigates 90 outside profiles
Cuts through seams
10. DEWALT Metal Shears Attachment, Impact Ready (DWASHRIR)
Feature
Able to cut up to 18GA material360 degree swivel head for maneuverability
Connects via standard 1/4-inch hex shank
Compatible with most 18V-20V impact driver and drills
Able to cut up to 18GA material
Connects via standard 1/4-inch hex shank
Compatible with most 18V-20V impact driver and drills
Recent Comments